Olympia Chimney Damper Repair Nationwide

Olympia Chimney Damper Repair: The Pasadena Owner’s Guide

Olympia Chimney damper repair in Pasadena typically runs $340-$620 installed, depending on whether the throat plate, frame, or full assembly needs replacement. We stock common Olympia Chimney damper configurations on our Pasadena service trucks and can usually complete the repair in a single visit. Most owners discover the problem on the first cold evening in November, when they open the damper and it sticks, drops halfway, or won’t seal at all, sending heated air straight up the flue all winter.

Call (213) 459-6058

Which Olympia Chimney Models This Applies To

Olympia Chimney manufactures throat dampers across several product lines, and the part you need depends on when your fireplace was built and which venting system was original. The OD-Series cast-iron throat dampers fit most Olympia Chimney masonry fireplace installations from 1998 to 2015, identifiable by the raised “OLYMPIA” casting mark and a 13-inch or 16-inch plate width. The newer OS-Series uses a stainless pivot assembly with a narrower 11-inch plate, common in factory-built fireplace installations after 2016.

Here’s the compatibility gotcha: Olympia Chimney switched pivot pin spacing between the OD-13 and OD-16 in 2008 without changing the model prefix. An OD-16 from 2005 has 7.5-inch pin centers; the same model from 2010 has 8-inch centers. Measure before you order. We carry both pin configurations in Pasadena, along with the stainless OS-Series hardware.

We source OEM Olympia Chimney dampers through Haven’s buying network, but we also stock quality equivalents from Gelco and Famco when the original part is back-ordered. The aftermarket pivot assemblies use 304 stainless rather than cast iron, which in Pasadena’s dry climate actually outlasts the OEM by several years. Level Two Chimney Pasadena is an independent service provider, not affiliated with Olympia Chimney.

Signs Your Olympia Chimney Damper Repair Is Failing

• The handle moves but the plate doesn’t. The pivot pin has corroded through or the cast-iron ear has cracked. In Pasadena, this usually happens after a summer of disuse when condensation sits in the throat; the plate is stuck in place while the handle spins freely.
• You feel cold air falling down the flue even when the damper is “closed.” The plate has warped or the frame has shifted, leaving a gap along the edge. A 3/8-inch gap around a 13-inch plate is equivalent to leaving a 4-inch window open year-round.
• The plate drops open on its own after you close it. The counterweight has broken off or the spring tensioner has failed. On Olympia Chimney OD-Series units, the cast counterweight is a single piece; when it goes, the plate has no hold position.
• Rust flakes fall into the firebox when you operate the handle. The throat frame is corroding from the inside, usually from a combination of combustion moisture and a missing or damaged chimney cap. This is progressive; the frame will eventually fail completely.
• The damper binds and requires force to open or close. Creosote has built up on the plate edges or the frame has distorted from heat cycling. In older Pasadena homes near Bungalow Heaven, we’ve seen frames bent from homeowners using fireplace tools to force a stuck plate.

Before

After

Replacement Cost & What’s Included

The range depends on three things: whether we can access the throat from the firebox or need to work from the roof, whether the frame is salvageable, and whether your flue liner needs resealing after the frame comes out. We quote in writing before any work starts, per Haven Standard Clause 1. Every repair carries the 365-Day Done Right Promise.

DIY or Call Us?

There is one safe check you can do yourself: shine a flashlight up the flue and look for the plate position. If it’s clearly stuck open or you can see a crack in the cast iron, you’ve confirmed the failure. Do not attempt to force the handle or reach up the flue to free it. The pivot assembly is under spring tension, and a slipped wrench can drive a pin into your hand or drop the plate unexpectedly.

Removing a throat damper requires working inside the fireplace opening with your arms extended upward, often in poor light, while handling a 12-pound cast-iron plate on a corroded pivot. The frame is mortared into the smoke chamber; disturbing it without knowing the liner condition can crack surrounding masonry. We bring a camera, document the full throat and smoke chamber, and quote only after you see what we see. The camera doesn’t negotiate, it just shows what’s there. Call (213) 459-6058 when you’re ready.

FAQs